When the moon burns and takes burbot
Night burbot fishing. Preparing for fishing. The alarm of fate rings in the sky, and blood is burning with excitement ... Burbot night fishing Night fishing requires some preparation for…

Continue reading →

real estate florida keys
Fishing at the pond in summer
What kind of fish and what gear do fishermen catch on village ponds. Fishermen at the pond in summer Of course, first of all, on a village pond in the…

Continue reading →

Fishing at night
Like many forest rivers, the Big Kokshaga is quite complex in nature and not immediately understandable even for a professional feeder or spinning. All these features must be recognized, as…

Continue reading →

Proper installation of a floating boil

How to mount a floating boilie and remove the “idle” bites? Basic rules to improve the performance of bites.

Novice anglers often encounter the problem of “blank” bites when fishing on boilies. The signaling device shyly peeps, the fishing line stretches slightly, but the long-awaited steam engine is still gone. This situation suggests that there is fish at the feeding point, she is interested in the nozzle, but refuses to bite. Numerous underwater shots, which can be seen on the Internet, often capture how a carp takes a boilies with a hook and spits it out without detecting it. At this time, the fisherman hears that the bite signaling device has tripped and immediately subsided. The reason for this phenomenon is the improper installation of the boil. It would seem that it could be simpler: I drilled a boil, did it with an awl, put a stopper and catch it. But not so simple. The smallest details are important in carp fishing. Proper presentation of the attachment is the key to successful fishing.

Proper installation of a floating boil
For installation we use a drill, an assembly awl, a stopper for a boil.

Installation of a boil

We will mount the boyle on a leash with a rig-ring. A plum floating boilie with a diameter of 12 mm is used. Hook on the leash of the sixth number. This is the limit value, if the boil was 14, then the hook needs a minimum of the eighth number, 16 boilies need the tenth hook and so on. First, with a drill, make a hole in the boilie.

Installation of a boil

The drill should be sharp enough, then the drilled core comes out in large parts.

Installation of a boil

A blunt drill can break the boil. Then, the mounting needle is threaded through the hole obtained,

Installation of a boil

clings to a loop on a leash,

Installation of a boil

closes and stretches through the boil.

Installation of a boil

A stopper is placed in the loop and the boil extends toward the stopper.

Installation of a boil

When installing the boil, it is important to observe the following rules
The hair length should be such that the mounted boil is 2-3 mm above the hook, and when it is turned to the tip, it touches it.

Installation of a boil

Boyle should not move through the hair, this is prevented by the loop node located inside it. If the lead material is thin enough and the boilie can move through the hair, then an additional silicone stopper must be placed under it. The position of the ring-ring, in the absence of a silicone tube, must be chosen so that the boil dipped in water is at an angle of about 45 degrees to the hook. Floating boilies need to be kept at a small distance from the bottom. Usually it is 2-2.5 cm. For this purpose, you can put a small lead pellet on a leash. After installing the boilie, the leash should be lowered into the water and, if necessary, correct the presentation. If everything is done correctly, then the effectiveness of bites should increase.

Dead zone
Birch trees were gilded, maples were covered with grease, and a red leaf fell on the still icy water, blue from the same blue sky, even cold in appearance. In…

...

Catch zander
Features of fishing zander on a spinning rod. Bait for pike perch. Places of fishing. Spinning fishing for zander has its own distinctive features, one of which is the impenetrability…

...

When a friend is under the ice
This morning, Sergei clearly caught Vitaly on the first ice. The fish seemed to go around the holes of his friend and took only from him. When another large fish…

...

Fishing at the pond in summer
What kind of fish and what gear do fishermen catch on village ponds. Fishermen at the pond in summer Of course, first of all, on a village pond in the…

...